A ten-minute lesson · one faucet · one drip

Why your hose bib leaks at the handle

The outdoor faucet is the simplest valve in your house — six parts, one moving piece. Once you see the inside, the drip explains itself, and so does the fix.

1 · The anatomy

Cutaway of a compression hose bib, side view

Water comes in from the pipe in the wall, waits in a chamber, and the only thing stopping it from pouring out the spout is a small rubber washer pressed down onto a hole called the seat. The handle turns a threaded rod — the stem — that lifts or lowers that washer.

wall supply pipe (from house) seat spout · hose threads packing nut packing (soft rings) stem rubber washer handle + screw water waits in the inlet chamber · washer on seat = closed
Six parts: handle, stem, packing nut, packing, washer, seat. Only the stem moves.
stem
threaded steel rod; the handle screws it up and down
washer
rubber disc on the stem's tip; it's the actual plug
seat
the ring the washer presses on; the hole to the spout
packing
soft rings squeezed around the stem so water can't climb it
packing nut
the hex nut under the handle; it squeezes the packing

2 · Closed vs. open

Tap to switch — watch the stem and the water
washer pressed on seat water stopped in the chamber stem shoulder seals against the bonnet ↑ handle turns → stem screws up/down → washer lifts off / drops onto seat
CLOSED — the washer is the plug. Nothing moves, nothing flows.
The hidden second seal. When the handle is turned fully open, the stem rises until a shoulder on it presses up against the inside of the packing nut. That shoulder becomes a seal of its own — which is why a weeping faucet often stops dripping when you open it all the way. It's called back-seating, and it's the trick you'll use.

3 · Where your drip comes from

Zoom on the packing nut, valve open

With the valve open, the inlet chamber is under full house pressure — and that pressure is pushing on everything, including up along the stem. The only thing stopping water from climbing the stem is the packing being squeezed tight against it. Packing is soft. Over years it compresses, hardens, and shrinks a hair. That hair is your leak.

packing nut worn packing — shrunk, hardened stem house pressure pushes UP on everything ← water climbs the stem, exits at the top of the nut this is the drip you see
The seal isn't a part — it's a squeeze. Lose the squeeze, get a drip.
Why your splitter doesn't leak. It's downstream of the stem entirely. The drip is upstream, at the one place in the whole system where a moving rod passes through a pressurized wall. Nothing else in your setup has that.

4 · The fix, in order

Restore the squeeze
FIX 1 · tighten the nut ¼ turn clockwise water ON while you turn · stop when the drip stops FIX 2 · repack nut backed off 2–3 wraps of Teflon packing cord water OFF · handle screw out · wrap · nut back on
Fix 1 works most of the time. Fix 2 is what you do when the packing has nothing left to give.
  1. Open the bib all the way first. Back-seating alone may stop the drip. If it does, leave it open forever and do your on/off at the splitter.
  2. Still dripping? Tighten the packing nut. Adjustable wrench on the hex under the handle, water on, ⅛ to ¼ turn clockwise. Stop the instant the drip stops. Overtighten and the handle gets stiff — back off a hair.
  3. Still dripping? Repack. Water off at the house shutoff, unscrew the handle screw, pull the handle, back the packing nut off, wrap 2–3 turns of Teflon packing cord (or plumber's tape in a pinch) clockwise around the stem, run the nut back down snug, handle on.
  4. Tight-space trick: a stubby wrench or a small crescent, and drag the sand bucket sideways an inch — it slides on turf with the leg still in it.
What this is not. A drip from the spout when the valve is closed is a different failure — a worn washer or a pitted seat. Same faucet, opposite end of the stem. Yours leaks at the handle while open: that's packing, every time.